2.0 TDI balancer shaft replacement instructions

something you need to ask , technical help here.

Moderators: water01, vwnutant, desertstorm

Post Reply
User avatar
Gazwould
UKPassat's Possie
Posts: 11895
Joined: Mon Dec 03, 2012 4:24 pm
Passat model: 1.9 AVF Sport

2.0 TDI balancer shaft replacement instructions

Post by Gazwould »

Alleged instructions.

Disconnect battery negative lead.
Slacken OSF wheel nuts.
Jack up car slightly to remove undershield and remove wheel and wheel arch liner.
Slacken auxiliary belt tensioner and lock off with suitable "pin" (allen key, drill bit or short handled screwdriver) and remove auxiliary belt noting its rotational direction.

Remove timing belt covers and crank pulley.
Drain oil.
Jack up higher and support with axle stands at suitable points to the rear of the subframe to allow room to work under engine.
Disconnect oil level sensor plug, remove sump, remove leftover silicone sealant from sump edge and crank carrier surfaces as you will need to reseal the sump for refitting - their is no sump gasket.

At this point you will see the balancer shaft unit bolted below the crank.
Lock cams and toothed crankshaft cog at TDC with appropriate locking tools.
This also locks the balancer drive cog on the back of the crank gear cog inside the sump area.
Support balancer unit and undo the 8 retaining bolts, if I remember rightly one of these is a long oil pump bolt and they are different sizes so use a piece of cardboard and pop them in the same positions on the cardboard noting that you are looking upwards at the balancer unit (renewal of the bolts is recommended as they are stretch type with additional angle stage tightening).
Wiggle the unit slightly and it should come away - it is HEAVY!!
Lower it carefully, it still has a lot of oil inside and remove from under the car.

Remove circlip from oil pump drive key hole (it's very small - renew it).
Drive key can be removed with a small magnet or by feeding it through from the balance shaft end.
Balancer unit is in two halves. Remove strainer pipe checking gauze is clear (clean pipe and gauze if necessary and renew pipe seal).
Undo retaining bolts again they may be different sizes and lift off top half leaving bottom half with balancer shafts in situ.
Shafts can be lifted out from bottom half of unit and gearing checked.
Replacement is usually no 2 shaft which has the drive key hole for the pump with a modified version (yours or exchange).
Clean visible oil channels on both halves and inspect shell bearings of balancer unit where shafts sit. Renew shells if worn or scored.

Apply thick oil or assembly lube to inside of shells and clean balance shaft journals.
When replacing a shaft ensure that the flat surface of the balance weight on each shaft sit level with each other (once their gear cogs have been reintroduced) in the bottom half of the balancer unit.
Apply assembly lube to balance shaft gear cogs.

Fit a new upgraded drive key of the correct length with retaining circlip.
Refitting is the reverse of removal noting that a special tool will be needed to retain the shafts in a specific position in the balance unit to align the drive gears and ensure they marry correctly before bolting the unit to the specific torque / angle settings.

A very small amount of backlash (backward rotation of the intermediate cog) should be present after refitting the unit.
This is necessary to avoid gear damage or excess wear.
You should have very slight rotational "play" for want of a better word when turning the lower gear cog against the intermediate one.
This is necessary to avoid gear damage or excess wear. Too tight against each other and the gear teeth will grind.

Seal sump with silicone sealant before refitting. Refit all other components removed applying correct torque settings.

CHECK: REMOVE ALL LOCKING TOOLS AND REFILL OIL!!

Rotate engine by hand a few turns to ensure free movement and no sticking of balancer unit gearing.

Reconnect battery and start up.
Image

Indigo Blue Sport Wagon


I'd give her some 'trivago'

This topic has 94 replies

You must be a registered member and logged in to view the replies in this topic.


Register Login
 
Post Reply