I have no stop start working, no auto hold working, I haven't 'exercised' the brakes to see if the ABS works and the 'handbrake' seems to be able to be removed / taken off without my foot being on the foot brake. Previous to these lights - all systems worked as expected.
I've borrowed a friends VCDS, but it is only V15.7.1 and it doesn't have all of the 'codes' or modules to read all of the car. It has, however, reset the ABS fault codes, but they come straight back again. They indicate a right rear sensor (OSR) so I've bought a new one and changed that out - no change (yes codes again reset via VCDS). I've continuity checked the wiring from sensor plug to ABS pump plug, both lines check out fine (pins 10 and 11 on the ABS plug). Using 'live data' from VCDS, I can get an indication of wheel rotation from the OSF and NSR wheels when rotated (didn't try NSF), but nothing from the OSR. When spinning the wheels by hand and getting a 'speed' readout on VCDS, I also got errors - only the OSF recorded - see attached spreadsheet - is this 'normal' or does it still point to the ABS pump module?
My thinking, is that when all wheels are stationary, there is no pulsing of the Hall effect sensors, so no output from one is the same as no output from another. Only when the wheels rotate, would you expect an 'output', thus I'm disregarding the magnetic (?) ring that the sensor reads from and heading more towards the ABS pump electronics (which I've sprayed with Servisol in case there was a dirty pin).
Am I heading in the right direction by looking to swap out the ABS pump electronics module? Anyone local to Newent, Glos, that has a more up to date VCDS that they are willing to let me try (at your premises if you are not happy to lend it to me) please?
Oh and how do I 'successfully' do a search on here for 'ABS Pump' when ABS is too short a term to search for???
Pic attached but not a good one of the left hand side lights - it's still going through the self test which is why there are more lights on and the LHS brake one is red.
VCDS read out is as follows:
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 3AA-614-109.clb
Part No SW: 3AA 614 109 AP HW: 3AA 614 109 AP
Component: J104 C2 450M V4F6 0030
Revision: --H07--- Serial number: 00000007626894
Coding: 0002992
Shop #: WSC 05311 000 00000
VCID: 7BF26FC33AF6C7E608-802E
1 Fault Found:
03842 - RPM Sensor Rear Right: Incorrect Signal
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 1
Reset counter: 246
Mileage: 192787 km
Time Indication: 0
Date: 2016.08.28
Time: 17:05:28
Freeze Frame:
Speed: 0.0 km/h
Hex Value: 0x0000
Bin. Bits: 00000000 00000000
Voltage: 11.75 V
Bin. Bits: 00011111
Count: 157
Hex Value: 0x0000
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1Kx-909-14x-44.clb
Part No: 1K0 909 144 R
Component: EPS_ZFLS Kl. 195 3501
Revision: 00H22000
Shop #: WSC 02069 000 90108
VCID: 397EB5CB704A35F65A-806C
1 Fault Found:
01316 - ABS Control Module
013 - Check DTC Memory - MIL ON
Freeze Frame:
Fault Status: 11101101
Fault Priority: 3
Fault Frequency: 1
Reset counter: 246
Mileage: 192787 km
Time Indication: 0
Date: 2016.08.28
Time: 17:05:28
Freeze Frame:
Voltage: 11.75 V
DD
Temperature: 20.0°C
RPM: 0 /min
Speed: 0.0 km/h
Speed: 0.0 km/h
Count: 0
-------------------------------------------------------------------------------
Address 53: Parking Brake Labels: 3AA-907-801.clb
Part No SW: 3AA 907 801 H HW: 3AA 907 801 H
Component: J540 EPB4 VW-86594 0010
Revision: H19 Serial number: 00000001606578
Coding: 0022167
Shop #: WSC 05311 000 00000
VCID: 3664BEF74154DA8EB7-8062
1 Fault Found:
01316 - ABS Control Module
013 - Check DTC Memory
Freeze Frame:
Fault Status: 01101101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 246
Mileage: 192787 km
Time Indication: 0
Date: 2016.08.28
Time: 17:05:28
Freeze Frame:
Voltage: 11.80 V
Count: 105
Speed: 0.0 km/h
Hex Value: 0x1263
Hex Value: 0x0001
Hex Value: 0x1010
The 'steering' VCDS module, when I do 'Advanced ID' gives me this:
Address 16: Steering wheel
Control Module Part Number: 3C9 953 501 BN
Component and/or Version: LENKS.MODUL 016 0140
Software Coding: 1182250000
Work Shop Code: WSC 00015
VCID: 76E47EF7C9D49A8E77-8022
Advanced Identification/FAZIT
Serial number: 20131008201503
Identification: ATW-001
Revision: FF010042
Date: 09.10.13
Manufacturer number: P1TC
Test stand number: 4097
Flash Status
Programming Attempts(application): 1/1/1
Successful Attempts(application): 1/1/1
Programming Attempts(data): 0
Successful Attempts(data): 0
Programming Status: 00000000
Flash Date: 10.06.01
Flash Tool Code(data): 00000 000 00000
Software
UDS: 00.00.01
UDS: 12.07.00
Theft prot.: 01.02.12
Diag: 00.0E.01
Diag: 00.09.00
Generic Net Mgt: 04.07.01
OSEK Net: 00.1E.03
Unknown: 03.0C.00
Generic Net Mgt: 04.07.03
LIN 2.0: 00.00.02
KWP2000: 07.04.00
Generic Net Mgt: 02.04.06
Misc.
Hardware number: 5K0 953 569 AB
Workshop System Name: J527
Equipment/PR Code: 3030303030303030
ASAM Dataset: EV_VW360TseerWheelUDS
ASAM Dataset Revision: A03004
VCDS Info:
Labels: 3C0-953-569.clb
ROD: ERROR - EV_VW360TseerWheelUDS A03004 (VW46)
The 'Park Steer Assist', when I do 'Advanced ID', gives me this:
Address 10: Park/Steer Assist
Control Module Part Number: 3AE 919 475 C
Component and/or Version: PARKHILFE 8K H06 0018
Software Coding: 118002
Work Shop Code: WSC 99999
VCID: 3F8ADBD3A66E1BC664-806A
Advanced Identification/FAZIT
Serial number: 28231329103692
Identification: ATW-001
Revision: --------
Date: 21.10.13
Manufacturer number: EB07
Test stand number: 0621
Flash Status
Programming Attempts(application): 1/0/0
Successful Attempts(application): 1/0/0
Flash Date: 10.02.18
Misc.
Hardware number: 7N0 919 475
Workshop System Name: J446
ASAM Dataset: EV_EPHVA81VW47X0000
ASAM Dataset Revision: 001006
VCDS Info:
Labels: 3AE-919-475.clb
ROD: ERROR - EV_EPHVA81VW47X0000 001006 (VW46)
Speed and error readout from 'hand spinning' the OSF wheel.