UKPassats

Did you ever find anyone? As I've got a b6 sitting on my drive that has a bust rear calliper and need someone to come and wind the motor back on the new one to fit it when it comes =[ stupid Eleci park brake. What happened to mAking things easy ay

I have a set of these and they do the job, there low not toooo bad could be harder depends what your trying to do.

This would be helpful if anyone knows also how do you get them out?

hello G-black havnt spoke in a while! well done on getting it all fitted in the end! i dont suppose you managed to get any pics of the bottom mounts for the rear bags and the top mounts fitted on the front bags? I still have my stuff wating around for me to boot my bum into gear lol! I have to make ...

The Fk streets though are not ultra low if you want pics of how they sit let me know. I don't think the rides that hard not way as hard as my Punto, dont get me wrong it is still not as spongy as standard but if you want the lows you have to pit up with it unfortunately. But you could get them and s...

Ive had a set. I thought they were ok for the money. Not ultra low but wheel sits in arch a tad on standards and have to slow riggggght down over speed bumps. Handling wise, yea there not racing shocks but are much more sturdy than standrd and I think they drive pretty well to be honest. I could go ...

Sorted wiper motor failed

Ant even get the wipers off. =| any ideas?? Tried wiggling them off made a little pulled still wouldn't come off!

hmm got my solinoids today not what i thought they would be back on the phone tomorow i think. they were only 3/2 valves n not 5/2 valves

Painting has begun on the tank thought first layer of primer applied

They plugged it in and all it said was that it wasn't working that was it. He tested power going to it and tested the earth and they were both ok.

Anybody know which relay is for the wipers?

I don't like the idea of it lol! Just a picture I found on stance work =| I couldn't believe it!! Still waiting on valves but having problems with my wipers so is on hold coz this could be an expensive one =[

These two diagrams show the coil-overs without them being joint they just sit on the nut! =s

http://www.dft.gov.uk/vosa/apps/recalls ... =Blank&tx=


They are deniying it :S

Chassis no. is WVWZZZ3CZ7P017*** I would say mine was in that group would you lot?

I go back to uni in the next couple of weeks so have milling machine and lathes there all good fun lol just have to get them to let me use there material! =p and then this will kick off! Also have to find some air fittings or that tank. Are the holes 1/2' bsp?

And I've checked the fuse in the engine bay and it's fine. Can't check the relay as don't know what one it is! could that be the problem? Never really known one to do really =s

It did look abit mad but would the bags twist if they are mounted to the top too? Hmm seems odd though as every other one has mounted plates at the bottom. If them mounting plates are goingfor owt, no doubt they will come in handy! I've just got to get some new nuts for the coilis so I can get them ...

Just stopped working? Any ideas? Were working fine the other day n now not?

http://2.bp.blogspot.com/_W5WkI0yANBk/S ... 0666-p.jpg

To me that looks like I dont have to have a plate on the bottom :O just need ont on the top?

What you guys think to that? I guess the bag wouldnt actually rotate if it is bolted to the top ?

Followed up my sample valves and they have been sent today got told they have had to be specially made or something :S hmm lets hope they work lol

Right had a little play at lunch. Just putting air in the tank from the compressor and the compressor started letting air out through the inlet port when I turned it off. Now have I got to have a non return valve on there to stop this? Lots of air seeped out because I didn't tighten the fitting up e...

Also G-black what thickness is the steel mounting plate?

Will go and get one in a minute and pm you it as soon as. This is just incas I decide to fit it on the standard shocks as I'm yet to decide. I think I'm going to ring fk and see if they will ship me a couple of nuts over. Spare so I can fit them onto the plates. Am in a saloon. And to be honist I'm ...

Ah ok nice one!! Well should be gettin my test solenoids tomorow so will take some pics and have sanded the tank down so it's scored up ready to paint!

Its just that silver nut i dont know if i take that it will release the seals for the oil in the shocks